Almost every piece of music you have heard is tuned so that A equals 440Hz. That number was standardised in the twentieth century largely for practical reasons and it became so entrenched that it went unnoticed. There is an alternative reference, 432Hz, that keeps resurfacing in acoustics, in tuning practice and in 432Hz MASTER-style retuning workflows. Here is what it actually does inside a DAW.
Where 432Hz comes from
The pitch of A is the number of vibrations per second. Fix that at 440 and you get one music. Fix it at 432 and you get another. The distance between them is 31.77 cents, which is roughly a third of a semitone. Small, but not invisible.
432 also has arithmetic structure that has nothing to do with acoustics. It is 27 times 16, and both factors are perfect cubes. Multiply it by 1024, a power of two, and you reach 442,368 exactly. Patterns like that are why the number attracts attention in a field that otherwise has no use for them.
What changes when you tune a mix to 432Hz
Retuning is a global pitch offset. Nothing is added, nothing is filtered out, and the relative intervals between your notes are untouched. What moves is the absolute pitch underneath everything.
- Tempo is unchanged. Time and pitch are independent here.
- The scale stays honest. A major third is still a major third.
- The whole mix sits lower. A 55Hz kick lands near 53.5Hz.
- High end loses its extreme brightness. Cymbals and air soften slightly.
- Headroom shifts. If you mix near a limiter ceiling, retune before you print.
Across most listeners the reported effect is reduced harshness. That is not a filter doing it. The whole production simply sits lower, and lower reads as softer.
Setting up 432Hz tuning in your DAW
You do not need to rebuild the session. Whether you use 432Hz MASTER, a stock utility, or your DAW's resampler, the sequence is the same.
Finish the mix first. Retuning a rough mix means doing the work twice.
Put the retuner on the master bus, after your limiter. It should be the last processing stage.
Enable it and bypass repeatedly to compare at matched loudness. Do not judge at volume.
Check a few specific references. Listen to the kick, the sub, the vocal sibilance and the top of the cymbals.
Which DAWs it works in
432Hz MASTER is a VST plugin, so it loads anywhere VST is supported. That covers Ableton Live, Logic Pro, FL Studio, Pro Tools, Cubase, Studio One, Reaper, Bitwig, Reason and essentially every other major DAW, on Windows and macOS. If you are searching for a 432Hz VST for Logic Pro or an Ableton pitch shifter, this is the category that matters, not the host.
Is 432Hz really the frequency of the universe?
Honestly, no one has demonstrated it. The universe is not known to resonate at 432Hz, and treating a tuning reference as a physical law overstates the case. What is real is the arithmetic, the different waveform, and the fact that plenty of people prefer how it sounds. That combination is worth testing on your own material.
Try 432Hz on your next master
432Hz MASTER converts 440Hz to 432Hz in one step, preserving tempo and tone. Works in every major DAW.
Frequently asked questions
How do I convert a song from 440Hz to 432Hz?
Print your mix, then load a 432Hz retuner on the master bus and set the reference to A = 432Hz. The whole signal shifts by about 31.77 cents and your tempo stays exactly where it was.
Will tuning to 432Hz ruin my mix?
No. At about 32 cents the shift is small, tempo and rhythm are unaffected, and no filtering is involved. The mix simply sits slightly lower and sounds slightly less bright.
What is the difference between 440Hz and 432Hz in cents?
31.77 cents, which is about a third of a semitone. That is small enough that many listeners cannot identify it in a blind test, though they often prefer it once told which is which.
Does 432Hz MASTER work in Ableton and Logic?
Yes. It is a VST plugin, so it loads in Ableton Live, Logic Pro, FL Studio, Pro Tools, Cubase, Studio One and any other DAW that supports VST.
Should I retune before or after mastering?
Early enough to hear how it affects your limiter and headroom, which usually means before the final print. You can also do it as the very last stage on the master bus.