The bass is the most consequential and least forgiving element in a mix. Every other instrument has to make room for it, it occupies the frequencies where masking is most damaging, and it is the element most often absent on playback systems. Getting it right matters more than any other single decision.

The fundamental is the note

A bass note is not a single frequency. It is a fundamental plus a series of overtones, and the relationship between the two determines whether the note is heard on a phone or only on monitors.

The fundamental is what you perceive as the pitch, and it is the part that carries the note. The overtones determine the timbre. On a system with no bass response, the fundamental is gone and what remains is the overtones, which is why a bass-only track can be completely inaudible on a phone while still sounding powerful on monitors.

Sub and the region above it

The low end is usually treated as one region, and this is where most problems come from. It is better understood as at least three layers, each with a different job and a different translation problem.

The sub region below about 40Hz is felt rather than heard, and almost nothing reproduces it. The fundamental region from 40 to 100Hz is the note itself, and this is where a bass and a kick either reinforce or fight. The low-mid from 100 to 300Hz is where bass guitars gain their body, and it is also where everything crowds together.

Reinforcement or conflict

When the kick fundamental and the bass fundamental sit at the same pitch, they reinforce. The listener hears one strong low end, and the two elements read as a single sound. This is the arrangement you want in most cases.

When they sit an interval apart, they fight. The result is a hollow, uneven low end where the kick disappears on some hits and the bass is inaudible on others. Level automation does not fix this reliably, because the two are competing for the same frequencies at different moments rather than in a consistent relationship.

Building a low end that works

1

Decide which element owns the low end. Usually the bass, sometimes the kick. Whichever it is, the other should sit above it rather than at the same frequency.

2

Filter everything that does not need low content. Guitars, snares, overheads and most pads. This is the single biggest improvement available to a crowded low end, because it removes energy rather than trying to balance it.

3

Check the low end in mono. A hard-panned bass vanishes, and two copies in opposition can cancel. This is invisible in stereo and obvious in translation.

4

Listen on a phone at the end. If the bass disappears entirely, the mix depends on frequencies most listeners cannot hear. The melody and arrangement should still work without it.

Low-frequency regions and their roles

RegionRoleTranslation risk
Below 40HzFelt impact, sub weightInaudible on nearly all systems
40 to 100HzThe fundamental, the note itselfWeak on phone, present on club systems
100 to 200HzWeight and bodyPoorly reproduced, but audible
200 to 400HzCharacter, some bodyReproduced well everywhere
400Hz and aboveOvertones, definitionFully reproduced

About sub-bass

Dedicated sub content, whether a sine below 40Hz or a sustained 808, is a stylistic choice with specific consequences. It is felt rather than heard, so on small systems it contributes nothing and the track loses weight. It also eats headroom, because it occupies a region with a lot of room before clipping.

If you are mixing for streaming, sub-heavy material is compressed harder by the platform's normalisation than material without it, which can leave the sub louder relative to everything else than you intended.

Retuning and the low end

All fundamentals move down after a retune, so the low end becomes denser. This is the single most important consequence of retuning for mixing, and it means a low end that was comfortable at 440Hz has less headroom at 432Hz.

Plugins like 432Hz MASTER preserve the relationship between your kick and bass, so the reinforcement stays intact. What changes is the spacing, and any fixed filter aimed at the old positions may need adjusting.

With RASTA 528Hz, the intervals change rather than slide, so kick-to-bass relationships can shift substantially and deserve a proper recheck.

The bottom line

Remove rather than balance, decide which element owns the low end, and check it in mono and on a phone. The bass is where translation problems begin, and it is where removing energy beats adding it.

Frequently asked questions

Why does my bass disappear on a phone?

Because the fundamental, which carries the note, sits below what a phone can reproduce. What remains is the overtones, and a bass-only track has very little of them. This is why a mix should work melodically and arrangement-wise even when the bass is inaudible.

Should my kick and bass be at the same pitch?

Close to the same pitch, so they reinforce and read as one strong low end. An interval apart causes them to compete, producing a hollow, uneven result that level automation does not fix reliably. Check the actual relationship against your bass line rather than in isolation.

How do I fix a muddy low end?

Remove energy rather than boosting. High-pass the elements that do not need low content, since guitars, snares and overheads contribute most of the buildup. Boosting the bass to be heard over the crowd only makes the crowding worse.

Why does retuning make the low end harder to mix?

All fundamentals move down, so elements that were spaced comfortably sit closer together and the low-mid has less headroom. An arrangement that was dense but working will cross the edge. The relationships are preserved, so it is spacing rather than balance that changes.

More from the atixUniverse blog