Chorus is the least sophisticated effect in production and the easiest to overuse. It takes one sound, detunes it slightly, mixes it back, and produces something wider and more interesting than it started. Because it is cheap and immediately noticeable, it is also the first thing added when a mix feels flat.
How a chorus works
A classic chorus splits the signal, delays one copy by a small amount between roughly 10 and 30 milliseconds, and modulates that delay time slowly with an LFO. The delay variation is what creates the movement, because it changes the pitch of the delayed copy continuously. The result is combined with the original, and the two are slightly out of phase with each other at any moment.
Because the two copies are never perfectly in phase, they partially cancel in the low-mid. This is the same mechanism that makes a doubled bass disappear in mono, and it is why a heavily chorused source loses low-end body. The effect works by creating a cancellation, and the cancellation is not selective.
Rate and depth
Rate is how fast the LFO moves, measured in Hz. Depth is how much the delay time varies, which translates directly to how far the pitch wavers.
The relationship between them determines whether the effect is heard as movement or as an artefact. A slow rate with high depth produces a wide, seasick wobble that is instantly obvious. A fast rate with low depth produces a shimmer that is often barely perceptible but adds considerable width.
The useful settings are usually a low rate between 0.2 and 1Hz with a modest depth, or a faster rate above 5Hz with very low depth. Fast, shallow movement is more useful in a dense mix because it does not create a rhythmic pattern that competes with the music.
Filtering is what makes chorus usable
A high-pass filter on a chorused return is close to mandatory. Because the effect creates phase cancellation across the spectrum, and because cancellation is most audible in the low-mid where the two copies are most similar, removing the bottom of the chorused signal removes the problem entirely.
In practice this means the low frequencies come from the dry signal and the chorus contributes only the upper-mid and top. This is not a compromise. It is the standard arrangement, and it is the reason a well-set chorus sounds expansive rather than thin.
Vocal chorus
On a vocal, a chorus is essentially a detuned double. It adds width and presence and it makes the vocal sound larger without adding level. It also makes the vocal harder to place, because a doubled source does not have a single point.
The practical guidance is to use it as a layer rather than as an insert when the vocal needs to sit clearly in the mix. Doubling the vocal, detuning the copy and panning it gives more control than a single insert, and it allows the dry vocal to remain a clean signal in the centre.
Setting a chorus properly
Start with the effect off and the dry level where you want it. The chorus should be an addition, not a replacement, and you cannot judge that if you are also hearing the change in the source.
High-pass the return at around 300 to 500Hz. This is the single most important setting and it is the one most often left off.
Set rate and depth together. Slow with shallow for movement, fast with very shallow for width. Avoid the middle ground, which is where the seasick artefacts live.
Automate the depth, not just the level. Reducing depth during quiet passages and increasing it in the chorus section gives the arrangement movement without the effect becoming a permanent feature.
Chorus settings by application
| Application | Rate | Depth | Filter |
|---|---|---|---|
| Vocal doubling | Fast, above 5Hz | Very low | 300 to 500Hz |
| Guitar width | Slow, around 0.5Hz | Low to medium | 400 to 600Hz |
| Pad movement | Slow, around 0.3Hz | Medium | 200 to 400Hz |
| Keys, wide | Fast, above 6Hz | Very low | 300 to 500Hz |
| Bass | Avoid | Avoid | Avoid |
Modulation and retuned mixes
Chorus and retuning interact in a way that is worth understanding. The chorus creates pitch variation to produce width, and a retune shifts the base pitch underneath it. The result is generally fine, and the movement masks the underlying tuning well.
The issue is that the chorus's high-pass filter interacts with a denser low end. After a retune with 432Hz MASTER, there is more low-mid energy competing with the effect, so a chorus that sounded clean before may need its filter raised slightly.
With RASTA 528Hz, where the harmonic content is redistributed, chorus and detuning content may overlap differently, so the result is worth checking rather than assuming.
The bottom line
Chorus is a width tool, not a character tool. Filter the bottom, keep the depth modest, automate it, and resist using it on anything that carries the low end.
Frequently asked questions
Why does chorus make my mix thin?
Because a chorus works by creating phase cancellation between the original and the delayed copy. That cancellation is not selective and is most audible in the low-mid, so the source loses body. High-passing the chorused return removes the problem.
What is a good chorus rate and depth?
Either slow with shallow for audible movement, or fast above 5Hz with very low depth for width without artefacts. The middle ground, moderate rate with moderate depth, is where seasick wobble lives. The right choice depends on whether the mix is busy.
Should I use chorus on a bass?
Rarely. The effect creates phase cancellation in the region where bass lives, so it reduces exactly the body the instrument needs. A small amount on a sustained sub line is occasionally effective, but it is not a default and a detuned double is usually better.
Should chorus be inserted or layered?
Layering gives more control. Doubling the source, detuning the copy and panning it lets the dry signal remain clean in the centre while the effect sits around it. An insert is quicker but takes the source with it, which is a problem for anything that needs to stay placeable.