Gain staging is the practice of setting sensible levels as signal moves through a mix. It is frequently taught as a discipline in its own right, and it is usually presented as being about the mix bus. That framing is misleading. Gain staging is about the levels entering each plugin, not about any single point in the chain.

Why it matters

Most plugins behave differently depending on the level they receive. Compressors have thresholds and ratios that only mean something relative to their input. A compressor set to threshold minus 12dB on a quiet signal does nothing, and the same setting on a hot signal compresses continuously. EQ is more predictable but can behave oddly when the signal is close to clipping, because nonlinearities in the plugin's own processing start to matter.

Retuning plugins are the clearest example. A pitch-shifting algorithm analyses the signal to determine its pitch, and a very hot signal gives it less headroom to work with, which can increase artefacts. Plugin developers generally expect roughly minus 12 to minus 6dBFS peaks on their inputs, and feeding them hotter than that is the most common cause of problems that are attributed to the plugin.

Read your meters properly

A peak meter shows instantaneous maximum level, which is what matters for avoiding clipping and it is not sufficient for judging loudness. A sustained level of minus 6dBFS peaks can sound extremely loud because the average level is high, and a level of minus 18dBFS peaks can sound quiet despite never approaching the ceiling.

The distinction between peak and average level is the whole reason a mix can be technically safe and still be too loud or too quiet. When you set a level, you are setting average loudness. The peak meter tells you whether you have left yourself enough room to process.

Fader positions are a diagnostic

On a mixing console, the faders tell you the story of the mix. If your vocal fader is far up and your drum faders are far down, the balance is being made at the faders rather than in the mix, which means it will not translate and every plugin you add is working on an already wrong signal.

A rough guide is that most mix faders should sit somewhere in the middle third of their travel, with the loudest sources near the middle and the quietest near the bottom. If you are riding two faders right at the top, the mix is too loud for the room you have available, and the solution is to pull the master down rather than to ride the sources up.

A gain staging pass

1

Set up the mix with all plugins bypassed. Build the balance from the faders alone. This is the mix's foundation and every later decision depends on it.

2

Pull the master down until peaks sit around minus 6dBFS. This gives you somewhere to go. A mix mastered at the ceiling has no headroom left for any processing, including the processing that would make it better.

3

Add processing one plugin at a time, checking levels after each. A compressor will reduce your level. Compensate so the balance you built stays intact, otherwise every subsequent decision is working from a different mix than you thought.

4

Check the inputs of the retuning plugin specifically. Peaks around minus 6dBFS give a pitch-shifting algorithm the headroom it expects, and this single check prevents more artefacts than any other change to your chain.

Reasonable peak levels by stage

StageTarget peakReason
Individual tracksMinus 12 to minus 6dBFSHeadroom for processing, no clipping
SubgroupsMinus 10 to minus 6dBFSRoom for group processing
Mix busMinus 6dBFS peakSpace for mastering and limiting
Plugin inputMinus 12 to minus 6dBFSWhat plugin developers assume
Final masterMinus 1dBTP or lowerReconstructed peaks, no clipping

Retuning and the pre-master level

Where you place a retuning plugin has a level consequence. On individual tracks, each source enters it at a controlled level. On the master bus, the entire mix enters it, and the level is whatever your mix bus is sitting at. This is the practical argument for a pre-master filter and a sensible mix bus level rather than a hot one.

Plugins like 432Hz MASTER are designed to be placed early, before the mix is consolidated, and using them that way avoids the density problem that makes master-bus processing harder on the algorithm.

The bottom line

Levels are the cheapest thing to fix and the thing that quietly undermines everything else. Set them deliberately, leave headroom, and recheck after every plugin that changes them.

Frequently asked questions

What peak level should I mix to?

Around minus 6dBFS peak on the mix bus. This leaves enough headroom for mastering and limiting, and it is far below the point where a plugin's own nonlinearity starts to affect its processing.

Does gain staging really matter in a DAW?

Yes, because the levels entering each plugin are the same whether the session is in a DAW or on a console. A compressor set relative to a threshold only behaves consistently if the signal arriving at it is at a predictable level.

Why do pitch-shifting plugins produce artefacts on hot signals?

The algorithm analyses the signal to determine pitch, and a very hot input leaves it less headroom to work with. Developers generally expect peaks around minus 12 to minus 6dBFS, and feeding them hotter than that is a common cause of artefacts attributed to the plugin.

Should the mix bus be at the same level as the tracks?

Not necessarily. The mix bus is typically quieter than individual tracks because it is summing many sources. The important thing is that it leaves headroom, and that you do not ride source faders up to compensate for a master that is too hot.

More from the atixUniverse blog