Mastering is mostly a negotiation about level. How loud the track should be, how much dynamic range to keep, what to give up to get there. A retune changes the inputs to that negotiation without changing the rules.
Gain reduction is not the goal
The number on a limiter's gain reduction meter is not a measure of quality. It is a measure of how much compression is happening, and more is not better. A limiter showing 6dB of reduction with a smooth gain envelope is doing good work. A limiter showing 12dB with an audible pumping envelope is doing damage regardless of how loud it makes the track.
The ceiling matters more than the reduction. 0dBFS in a fixed-point format is absolute, and exceeding it produces clipping, which is broadband distortion rather than controlled limiting. In a float session you can exceed it, but you still have to dither down to the delivery format eventually, and a track that relies on intersample peaks will sound duller than its meters suggest.
Target loudness depends on the destination
Streaming platforms normalise loudness, so a master that is dramatically louder than the rest of the catalogue gets turned down anyway, and the density you paid for in compression is simply removed. For most destinations, a target integrated loudness somewhere between minus 9 and minus 11 LUFS is a reasonable place to start, with the lower end of that range giving streaming more headroom to work with.
True peak is worth targeting explicitly. If your ceiling is set to 0dBFS sample peak, you can still exceed 0dBTP because the DAC reconstructs a waveform that passes between the samples. Staying at minus 1dBTP or so avoids that.
What a retune changes at the mastering stage
A plugin like 432Hz MASTER lowers the fundamentals across the whole mix. Two things follow.
First, low-frequency content is slightly denser, and low frequencies are where loudness and headroom interact most awkwardly. A limiter working hard on a dense low end will duck the entire mix on every bass hit, and that pumping is the most audible artefact of over-limiting.
Second, if you have gentle high-pass filters placed assuming the previous low end, the region just above them has changed. Small cuts aimed at old positions may now be doing nothing, while the real congestion sits slightly lower.
With RASTA 528Hz, where intervals are redistributed, the spectral balance can change more substantially, so a full recheck of the chain is warranted rather than just the low end.
Mastering after a retune
Start from a mix that is not already at the ceiling. A retune can add density that pushes the mix louder than it was. Before reaching for a limiter, check whether the mix bus is simply hotter than it was before.
Address low-end congestion before limiting. High-pass elements that do not need low content. This reduces the density the limiter has to work against and reduces pumping.
Set the ceiling and check true peak, not just sample peak. Leave a small margin below 0dBTP and verify with a dedicated meter.
Listen for pumping on the bass, not for volume. A limiter at 4dB of reduction that does not pump is a better master than one at 8dB that does.
Headroom, ceiling and target levels
| Setting | What it controls | Common mistake |
|---|---|---|
| Ceiling | Maximum output level | Setting it at 0dBFS sample peak |
| True peak | Reconstructed waveform maximum | Ignoring it entirely |
| Gain reduction | How much limiting occurs | Chasing a target number |
| Integrated LUFS | Average perceived loudness | Targeting far above the platform norm |
| Dynamic range | Difference between quiet and loud | Compressing before fixing arrangement |
The bottom line
After a retune, the mastering decisions that change are about density, not about level. Reduce the crowding first, limit second, and judge the result by whether the bass pumps rather than by how loud the meter reads.
Frequently asked questions
How much gain reduction is too much?
There is no number, but pumping is the real limit. A limiter at 4dB of reduction with a smooth envelope is working well. At 8 to 12dB you will usually hear the envelope working, particularly on bass-heavy material, and the trade is rarely worth it.
What loudness should I master to for streaming?
Somewhere between minus 9 and minus 11 LUFS integrated is a reasonable target, with the lower end giving streaming normalisation more headroom. Going significantly louder means the platform turns it down and removes the density you paid for.
Do I need to worry about true peak?
Yes. A ceiling set to 0dBFS sample peak can still exceed 0dBTP because the DAC reconstructs a waveform that passes between samples. Staying around minus 1dBTP avoids the resulting distortion.
Why does a retuned mix need more low-end work at the mastering stage?
All fundamentals move down, so low-frequency content is denser than it was. A limiter working against denser low end ducks the whole mix on every bass hit, and that pumping is the most audible artefact of over-limiting.