Sidechain compression is a compressor triggered by a second signal, usually the kick. When the kick hits, the compressor on the bass ducks, and the bass sits underneath instead of fighting. It is an unusual effect in that it is entirely rhythmic, and it is one of the most recognisable production techniques in electronic music.

How it works

A standard compressor has two jobs. It listens to its own input and reduces gain when that input gets loud. A sidechain compressor listens to a different input entirely. The signal being compressed never causes the compression, so a bass sitting at a constant level will be reduced every time the kick triggers, and rise back between hits.

The important consequence is that the amount of reduction depends on the relationship between the two signals, not on the bass's own level. A louder kick produces more ducking. This is why sidechain settings are set with the kick in place rather than in isolation, and why they stop working properly the moment you change the kick.

Why it works musically

The reason sidechain ducking became so widespread is that it solves a real problem. A synth bass at a sustained level competes with the kick for space in the low-mid region, and the competition is at its worst on every beat, because that is exactly when the kick arrives.

The static solution is to give the bass and the kick different frequency regions, which is proper mixing and always worth doing first. But many genres place the bass fundamental in the same region as the kick, because that is where the music wants them. Sidechain compression is how producers accept the overlap and manage it rhythmically instead.

Pump versus groove

The difference between a pump that works and one that does not is entirely in the timing. A good one is fast in and slightly slow out. The reduction should be essentially complete by the time the kick's attack has passed, and the recovery should take long enough that the bass does not jump back up audibly between hits.

A fast release on a fast tempo produces a fluttery, uneven tone where the bass level rises and falls on each subdivision. A slow release leaves the bass permanently quieter for the second half of each beat. Both are recognisable failures, and both are fixed by the same adjustment, which is a slightly slower release than instinct suggests.

Setting it up

1

Get the static balance right first. Filter and EQ the bass and kick so they occupy reasonable regions before adding any dynamic processing. Sidechain is a management tool, not a substitute for arranging them properly.

2

Trigger from the kick, not from a separate envelope. Using the kick as the trigger means the ducking is automatically correct every time the kick changes, and you do not have to redraw anything after editing.

3

Set the threshold high enough that only the kick triggers it. If the bass is triggering the compressor on its own, you have a level problem that the sidechain will not solve.

4

Watch the recovery, not the reduction. The amount of gain reduction tells you nothing useful. Listen for whether the bass returns smoothly and consistently on every beat.

Effect of the main parameters

ParameterEffectCommon mistake
ThresholdHow loud the trigger must beToo low, so the bass triggers itself
AttackHow fast the duck beginsToo slow, so the kick transients overlap the bass
ReleaseHow fast the bass returnsToo fast, causing flutter between beats
RatioHow hard it ducksOver-reducing so the bass disappears
Release timeTail of the recovery curveChasing exact millisecond values by ear

Sidechain and retuned mixes

Sidechain relationships are level relationships, and a retune does not change levels. What it changes is the frequency content being compressed, and the low-mid density that made the ducking necessary in the first place. After a retune with 432Hz MASTER, the kick and bass are closer together in frequency than they were, so the compression may be doing more work than it needs to. Check whether the static arrangement still needs the help before keeping the aggressive settings.

With RASTA 528Hz, the Solfeggio redistribution changes the relationship between the bass and kick harmonics more substantially, so a previously useful ducking depth can become either unnecessary or insufficient. It is worth re-tuning the threshold and release rather than carrying the old settings across.

The bottom line

Sidechain compression is a legitimate tool, but it is a last step rather than a first one. Get the static balance right, and reach for the compressor only when the overlap is genuinely rhythmic and genuinely needs managing.

Frequently asked questions

Should I use sidechain compression on every mix?

No. It is a stylistic choice that has become conventional in some genres, particularly electronic music. In acoustic and many traditional contexts it would be wrong. Using it where the arrangement does not call for it makes the mix sound processed rather than produced.

What sidechain release time should I use?

Slow enough that the bass does not audibly jump back between kicks, and fast enough that the second half of each beat is not permanently quieter. The instinct to set it very fast usually produces flutter, and the right value is more often slightly longer than expected.

Does sidechain compression affect the kick?

Only if the kick is the sidechain source, in which case the compressor is on the bass and the kick is the trigger. The kick itself is not being compressed by its own compressor, though it is often compressed separately for control.

Why does my sidechain pumping sound wrong after I retuned the mix?

Sidechain relationships are level-based, but a retune changes the frequency content being compressed and how densely the kick and bass overlap. After a retune, the old threshold and release may be too aggressive or too gentle for the new relationship, so they need rechecking.

More from the atixUniverse blog