The low end is where a mix most often fails, and it is also the region that is hardest to evaluate while you are working on it. You get used to what you have been hearing for an hour. A structured set of checks is more reliable than another pass of listening.
Run the checks in order
The sequence below moves from the most fundamental to the most subtle, because fixing them in a different order usually means fixing them twice. A low-mid problem will make a kick-to-bass check meaningless, so the filtering comes before the relationship check.
The seven checks
One. Filter everything that does not need low content
Guitars, snares, overheads, room mics, most vocal recordings and most pads should be high-passed. This is the single biggest improvement available to a crowded low end, because it removes energy rather than trying to balance it. Do this before anything else, because everything else is harder to judge while the low-mid is full.
Two. Check the kick-to-bass relationship against the actual bass line
Play the bass part on its own, note the notes it plays, then check whether the kick fundamental sits at those same notes. Close agreement reinforces. An interval apart competes, and level automation will not reliably fix it.
Three. Sum to mono and listen at a moderate level
At high level, missing low end is masked by the rest. At moderate level your ear adapts less and the problems are easier to hear. A bass that vanishes in mono is usually hard-panned, which is a one-second fix.
Four. Look at the sub region deliberately
Below about 40Hz there should generally be nothing except intentional sub content. Handling noise, DC offset and accumulated low-frequency energy from reverbs and pads all accumulate here, and they are easy to miss because they are inaudible in isolation.
Five. Check the low-mid for build-up over time
Static EQ changes tone, and dynamic EQ or a compressor changes it over time. A mix can sound fine at the start of a section and muddy eight bars later as resonance accumulates. Play the section through rather than sampling it.
Six. Listen on a phone
Two minutes. A mix that depends entirely on low frequencies to make sense will lose its foundation for a large share of listeners. The melody, arrangement and texture should all work when the bass is inaudible.
Seven. Re-measure after any retune
All fundamentals move down, so the low end is denser after a retune. Recheck the filters and the kick-to-bass relationship rather than assuming they still hold, since the spacing has changed even though the balance has not.
The checklist at a glance
| Check | Catches | Time |
|---|---|---|
| Filter non-bass sources | Low-mid buildup from unneeded content | As long as it takes |
| Kick against bass notes | Fighting or hollow low end | One minute |
| Mono fold-down | Panning and phase problems | One minute |
| Sub region | Rumble, DC, accumulated energy | Thirty seconds |
| Build-up over time | Dynamic low-mid congestion | One playthrough |
| Phone playback | Dependence on inaudible frequencies | Two minutes |
| Post-retune recheck | Stale filter and spacing assumptions | Two minutes |
Where retuning fits
Retuning should happen before this checklist rather than after it, because it changes the spacing that checks two and seven are verifying. Using 432Hz MASTER and then running the checks properly is more reliable than retuning a mix whose low end was never verified.
With RASTA 528Hz, where intervals are redistributed rather than lowered, the kick-to-bass relationship can change substantially, so check two deserves a proper repeat rather than a confirmation.
The bottom line
Seven checks, roughly five minutes, and it will catch more low-end problems than an hour of mixing. Run it on every export.
Frequently asked questions
What should I check before exporting a mix?
The low end is the priority: filter everything that does not need low content, verify the kick-to-bass relationship against the actual bass notes, sum to mono, check the sub region for rumble, listen for build-up over time, and play it on a phone. Roughly five minutes catches more than an hour of mixing.
Why does my mix sound muddy at the end of a section?
Because low-mid energy accumulates over time. Reverbs, pads and resonance all contribute, and a static EQ setting cannot follow a change that happens gradually. Play the section through rather than sampling it, and consider dynamic processing if the build-up is consistent.
How often should I run a low-end check?
On every export. The checks are fast and the low end is where translation problems originate, so it is the region least worth trusting to memory. Particularly after a retune, because the spacing changes even when the balance does not.
Does retuning invalidate my low-end settings?
Partially. All fundamentals move down, so the low end is denser and any filter aimed at a specific interaction may be aiming at the wrong place. The balance between kick and bass is preserved, so the relationship holds, but the spacing and the filter positions are worth rechecking.